Rheem Oil Furnaces  (6)

With ongoing efforts from governments across the globe to reduce carbon emissions and with an ever greater focus on sustainability, it is vital that the HVAC sector does its part in becoming more environmentally conscious. And, while there have been steps to become more sustainable, there is a huge amount that still needs to be done to make sure that many of the targets that have been set are attainable. In buildings, both large and small, industrial heating accounts for roughly two thirds of industrial energy demand and around a fifth of global energy consumption. Figures like this show the need to have efficient and environmentally-friendly HVAC equipment in place to make the crucial steps towards reducing the contributions these systems make to our carbon footprint. High energy consumption in construction sector A 2019 report by The International Environment Agency (IEA) showed that the buildings and construction sectors combined were responsible for over 30% of global energy consumption and nearly 40% of carbon emissions. This is indicative of the steps the sector needs to take to play its role in a more eco-friendly society, some of which are already underway. However, much more needs to be done if the UK is to reach its goal of reaching net zero carbon emissions by 2050. As we envisage what a post-COVID world might look like, businesses and governments are continuing to put sustainability and lower carbon emissions at the forefront of their planning and the HVAC sector is certainly no exception. But with change in the sector a daunting prospect, decision-makers often don’t know where to start. Smart Technology use in HVAC systems Smart HVAC uses sensors that integrate with a building’s automation system With the constant growth and greater deployment of smart technologies within the HVAC sector, this is certainly a way that systems can become more efficient. Smart HVAC uses sensors that integrate with a building’s automation system. These sensors then collect information about conditions throughout the building. Heat waves are now a far more common occurrence in the United Kingdom. The Met Office estimates they are up to 30 times more likely and will be a bi-annual occurrence by 2050. It is important that any uptake in HVAC usage doesn’t lead to a drastic increase in emission generation. This is one of the areas where smart systems will become crucial. Many scientists have been unequivocal in their sentiment that heat waves are a cause of greater emissions and expect temperature records in the UK and Europe to be broken more regularly, so sites will need to be equipped to handle these conditions. Regulating temperature with hand-held devices With wireless systems now much more commonplace, temperatures can be controlled easily from hand-held devices. With these new technologies, those managing the systems can also benefit from remote monitoring and maintenance, reducing the need to travel to the site for yet another environmental incentive. To accompany the smart systems, equipment including smart thermostats can be installed to maximize HVAC efficiency. Other smart systems available to businesses include smart furnaces and air conditioning units that are far easier to operate than their traditional counterparts. Reducing unnecessary ventilation While global temperatures continue to rise, air conditioning usage has increased and has contributed to greater levels of energy usage. A huge amount of needless emissions are generated by unnecessary ventilation, contributing heavily to heat loss and overall energy wastage. Recirculation of air is a traditionally lower energy cost method of retaining heat and keeping emissions low, however, we must be mindful of the risks associated with recirculating air. The risk of circulating diseases is negated somewhat with heat recovery ventilation, which both removes the risk of disease spreading and improves energy consumption. Efficiency performance of new AC units Air conditioning units in particular contribute significantly to a building’s energy consumption Air conditioning units in particular contribute significantly to a building’s energy consumption, equating to 10% of the UK’s electricity consumption and as such it is important that we bear in mind ways to counteract the emissions this creates. Global energy demand for air conditioning units is expected to triple by 2050, as temperatures continue to rise year on year. The efficiency performance of new air conditioning units will be the key, when it comes to ensuring that escalating demand does not equate to greater emissions. Another issue for suppliers and manufacturers to address is differing rates of consumption for AC units in different countries, with units sold in Japan and the EU typically more efficient than those found in China and the US. Modularization Modular HVACs have also become increasingly popular in recent years. Modular HVACs are responsible for heating, cooling and distributing air through an entire building, with their increase in popularity largely down to their greater levels of energy efficiency, cost effectiveness, flexibility and substantial ease of installation and maintenance. Modular HVACs can be tailored specifically for workspaces and they often allow work to be done on the systems without disturbing the workforce, achieved primarily through rooftop placement. Commercial workspaces are larger and often require differing needs to residential properties and can cater to a wide range of the specific requirements of work and commercial spaces. As we strive for lower carbon emissions, it seems that this trend will continue and will become a key area in reducing emissions that HVACs have traditionally generated. System maintenance and training To meet government and industry requirements, many new buildings will require HVAC systems that can be maintained simply in order to perform in a more energy efficient way. Many companies are looking at ways to become climate neutral and significantly reduce their footprint Many companies are looking at ways to become climate neutral and significantly reduce their footprint. Companies are following the likes of German-based company, Wilo Group, who have announced they are committing to sustainable manufacturing by developing a new carbon neutral plant and HQ in the next few years. Lowering carbon footprint As we continue to move towards an ever more environmentally conscious society, it will be of paramount importance for companies, governments and the public to think about ways in which we can lower carbon emissions. Smart technologies will certainly be at the forefront of this, negating many needless journeys and making it easier for industries to adjust settings and tackle issues remotely. Greater levels of training will help equip us with the tools to make sure we are best placed to reduce emissions and be more sustainable as a result. While the steps outlined above do show some progress and measures we can take, there is far more that we can do as a sector to significantly reduce HVAC’s carbon footprint and once we have moved beyond the impact of the COVID-19 pandemic, this will surely be at the front of industry leader minds.

As the UK continues to battle through the coronavirus crisis, HVAC business owners and installers can be putting some of their enforced downtime to good use. This period of subdued trading is a rare opportunity to get into better shape for when economic activity picks up. One way of doing this is by sharpening the focus on markets which promise strong growth – and few markets are growing faster than that for heat pumps.   The potential here is huge. Some 28,000 heat pumps are currently installed in the UK every year, and before the pandemic this number was rising annually at a rate of 15-30%. That equates to sales doubling every three to five years. New-builds account for the majority of those sales, but 30% are retrofits, and about 30% of those retrofits are in private residences. This means there’s a big opportunity for doing conversions from oil boilers to heat pumps at rural homes not connected to the gas grid. The ‘New Normal’ and Heat Pumps It is only realistic, of course, to expect a lingering dip in HVAC sales of all kinds, including heat pumps, until the post-pandemic world gets back on its feet. But when we do turn the corner into the ‘new normal’, heat pump sales will again climb strongly. One reason for this is consumer demand, the other is government policy. End-users are now increasingly aware of the dangers and disruptions threatened by carbon emissions and climate change – informally known as ‘the Blue Planet Effect’ – and more are being guided by their consciences to make environmentally-responsible heating choices. An Expected Spike In Demand Many end-users are also encouraged by the prospect of receiving payments from the government through the Domestic RHI tariff. When we do turn the corner into the ‘new normal’, heat pump sales will climb strongly If RHI tariffs are the carrot, however, the government is also going to wield a big stick. The Chancellor’s spring statement last year dropped the bombshell that low-carbon heating systems, not fossil-fuel heating, should be installed in all new homes built after 2025. Though this policy might perhaps get slightly delayed and diluted, there can be no doubting that radical change is on the way.           With all this in the pipeline, the industry should be preparing now to cope with the increased demand. But there’s some way to go: of the UK’s 120,000 registered gas engineers, merely 600 or so are MCS-registered to install heat pumps. Many more will be needed. MCS Certification Some installers are already recognizing this opportunity. Some 28,000 heat pumps are currently installed in the UK every year, and before the pandemic this number was rising annually at a rate of 15-30% This is evident in the heightened level of interest in the one-day introductory heat pump courses run nationwide by the Viessmann Academy. These courses provide a useful overview of what heat pump installations involve, helping participants decide whether or not they would like to go on to qualify with the MCS quality assurance scheme. This is a crucial decision, because having MCS certification is an obligation when installing equipment eligible for Domestic RHI payments. Some course participants decide to take the next step to MCS certification straight away, others decide to wait a while – but standing still in a fast-moving market can mean getting left behind! F-Gas Certification So what else must HVAC businesses and installers consider about heat pumps, in order to stay ahead of the game? In addition to MCS certification, F-Gas certification is also necessary when split air source heat pumps are installed. This is because the outdoor and indoor units have to be connected on-site with refrigerant pipework. Some installers choose to get F-Gas certified themselves, others sub-contract this part of the job to someone who’s suitably qualified. Of the UK’s 120,000 registered gas engineers, merely 600 or so are MCS-registered to install heat pumps It is possible to sidestep this need, however, when it is appropriate to install a monobloc heat pump – and the widening choice and affordability of monobloc designs is making them appropriate for a wider range of properties. A good example of this is Viessmann’s new Vitocal 100-A, an outdoors unit which has no need for a complementary indoor unit and is also easy to install because most components are integrated in the unit. New, compact and affordable air source heat pumps such as this, offering much-needed space-saving solutions for urban homes, are another reason why the heat pump market will boom. The Challenges Of Heat Pump Installation Though technological advances are making things easier, installing a heat pump isn’t ever going to be quite as straightforward as replacing an old boiler with a new one. Before starting an installation, first it is necessary to assess whether a heat pump is suitable for the property. This means checking that the property is well-enough insulated; checking the existing system’s radiators, which may need supplementing or replacing with bigger radiators or underfloor heating because of the lower flow temperatures of a heat pump system; and calculating the required size of the heat pump according to the building’s heat loss (and not including hot water demand). This period of subdued trading is a rare opportunity to get into better shape for when economic activity picks up At the installation stage itself, much of the work will be familiar to boiler installers, though weather compensating controls are obligatory for all MCS-approved work and as part of building regulations Part L. It’s also important to note that planning permission requires minimum distances between the heat pump’s outdoor unit, the plot’s borders, and neighboring properties. If this seems complicated, it doesn’t have to be: some heat pump manufacturers provide a calculator to simplify the task. Now Is The Time To Be Proactive Just as installers need a little time to assess whether a property should switch from a boiler to a heat pump, end-users also need a little thinking time, to consider adopting a technology new to them. By being proactive, HVAC businesses and installers can reap what they sow When customers get in touch because their existing boiler has broken down, the pressure for a quick fix can rule this out. But right now, when many of us have time on our hands, there’s the chance to inform customers of alternative heating solutions before their boiler needs replacing. Taking such pre-emptive action, by emailing information or mailing leaflets to customers, does require a little effort, but at least now there’s the time to do it. We are heading into a new era which will see boiler sales decline while heat pump sales rise. By making preparations for these profound changes, and by being proactive, HVAC businesses and installers can reap what they sow.

Manufacturers continue to make improvements in heat-pump technology, including higher efficiencies, contractor-friendly designs, and innovative extras like two-stage compressors that allow them to run at lower speeds and cut down energy use and homeowners’ bills. Below is a sampling of six of the latest products to hit the heat pump market. Nortek Global HVAC introduced the W-Series of air conditioning and heat pump equipment for residential and light commercial applications, completing its redesign of Gibson®, NuTone®, and Frigidaire® branded 1.5- to 5-ton, single-phase air conditioning units and heat pumps. The redesign offers contractors a ‘good-better-best’ strategy (the premium F-Series, the mid-range E-Series, and the economically-priced W-Series) to accommodate varying consumer price ranges. Coil-Protecting wire guard The W-Series heat pump is available in 14- and 16-SEER models. Standard features include Copeland scroll compressors and a liquid line filter-drier for field installation in an accessible position to facilitate easy periodic change-outs. It also has a coil-protecting wire guard that adds cabinet structural integrity and holds a plastic mesh in place to safeguard against hail and accidental contact damage, plus an anti-corrosive polymer drain pan with more drainage holes to eliminate potential standing water. On the unit’s exterior cabinet, above the refrigerant access port, is a weather-proof QR code called ‘Charge Me’ that can be scanned to access Nortek’s charge assist tool. “The new W-series of heat pumps recently introduced by Gibson, Frigidaire, and NuTone features a high-tech way to charge,” said Dave Garvin, product manager, Nortek Global HVAC. Variable Speed Heat Pump Rheem’s next generation Prestige® heat pump harnesses the power of the new EcoNet Smart Thermostat “The proprietary website helps account for subcooling, fixed orifices, thermostatic expansion valves, ambient temperature at time of charging, lineset length, and other variables that can trip up contractors when charging any heat pump brand.” The Rheem® Prestige® Series EcoNet®-Enabled Variable Speed Heat Pump features a contractor-friendly design, which means expanded valve space and triple service access, for fast and easy install and repairs. Corner-service access allows optimal access to internal components, while individual louver panels speed coil cleaning and cabinet reassembly. Plus, Rheem’s next generation Prestige® heat pump harnesses the power of the new EcoNet Smart Thermostat, which provides control, monitoring, and one-touch alert capability. Proper installation and reduced time “Rheem’s Prestige Heat Pump powered by our EcoNet Smart Thermostat keeps contractors in control,” said Ryan Teschner, product manager for Rheem Mfg. “From real-time alerts and system notifications to a charge mode capability, which allows for proper installation and reduced time on the job, Rheem’s heat pump increases job site efficiencies and reduces labor costs for contractors.” The hybrid electric Voltex® from A. O. Smith has an energy factor (efficiency based on the amount of hot water produced per unit of fuel consumed over a typical day) of 2.3, and is Energy Star® qualified. “Heat pump water heaters use electricity to pull heat from the surrounding air rather than generating their own heat,” said Brandon Stepanek, national field marketing manager at A. O. Smith. Reducing greenhouse gas emissions Carrier’s Hybrid Heat systems automatically switch between electric and gas heating “This means that they can be a logical choice for dedicated green home builders interested in enhancing energy efficiency. Because a heat pump water heater uses energy efficiently, it can save customers up to 10 percent on energy bills, which adds up to thousands of dollars over the life of the water heater,” he continued. “The significant reduction in electricity use also has a direct effect on reducing greenhouse gas emissions.” Carrier’s Performance™ Series heat pumps offer a range of efficiencies that start at 14 SEER and reach 17.5 SEER and up to 9.5 HSPF. Combining a gas furnace, an electric heat pump, and a compatible thermostat, Carrier’s Hybrid Heat systems automatically switch between electric and gas heating to optimize the efficiency of each fuel source, helping defend homeowners against utility cost fluctuations. They have Energy Star designation. Carrier indoor furnace “Our microtube coil technology saves space and provides lasting comfort with its corrosion-resistant construction,” the company stated. “In addition, some models include innovative extras, like a two-speed compressor for added benefits like higher efficiency and even, consistent comfort. When installed with a custom-matched Carrier indoor furnace or fan coil and a Côr® Wi-Fi® thermostat, our two-stage heat pumps can operate on low stage up to 80 percent of the time to keep airflow and temperatures even and consistent while adding humidity control during cooling operation.” Heating operation is rated down to minus 5˚F outdoor temperature Fujitsu General America Inc. recently debuted the RGLX Series, three medium-static pressure ducted indoor units for the single-zone Halcyon mini split line. They have sufficient static pressure to heat or cool a whole house. Heating operation is rated down to minus 5˚F outdoor temperature. The 12,000-, 18,000-, and 24,000-Btuh models are Energy Star qualified. V-Shaped heat exchanger Units are available in seven sizes ranging from 12,000 to 48,000 Btuh, with efficiency ratings up to 21.3 SEER. The evaporators are slim enough to fit most ceiling spaces, making them ideal for hidden installations, while the condensing units can be installed below a window or in a narrow space. The new models can be installed in applications that require static pressure up to 0.80 inches of water column and offer maximum piping lengths of up to 246 feet. A built-in drain pump with 33.5 feet of vertical lift comes standard. “The combination of the V-shaped heat exchanger, air stabilizer, and the energy-efficient DC fan motor results in high efficiency and quiet operation,” Fujitsu wrote in the product specs. Customized indoor comfort The Goodman GSZC18 Heat Pump features the next-generation Copeland Scroll™ two-stage compressor coupled with Goodman’s ComfortBridge® communicating technology to deliver up to 19 SEER and 10 HSPF performance. ComfortBridge ‘off-the-wall’ technology gives contractors more installation options and intelligent controls. It works with any thermostat, including single-stage ones. ComfortBridge constantly gathers data, making automatic adjustments for peak performance ComfortBridge constantly gathers data, making automatic adjustments for peak performance, using the minimum energy needed for consistent, customized indoor comfort. A companion CoolCloud™ app connects technicians wirelessly via Bluetooth to ComfortBridge. Advanced ComfortAlert™ Diagnostics constantly monitor the system, reducing failures and pinpointing trouble spots. “Our 18-SEER heat pumps provide high-efficiency, energy-saving indoor comfort with the ease of installation as compared to less sophisticated products,” said Cory Gottfredson, senior product manager, Outdoor Split Systems for Goodman. Compressor crankcase heater “We have incorporated ComfortBridge technology to optimize installation while allowing homeowners to use any thermostat. This truly enhances both operation and installation, freeing contractors from hassles and leaving money in the hands of homeowners where it belongs.” The scroll compressor inside the GSZC18 is designed with fewer moving parts, and the high-efficiency, two-speed electronically commutated condenser fan motor with advanced fan design provides quiet airflow. Other features include SmartShift® technology with short-cycle protection, a bi-flow liquid-line filter-drier, suction line accumulator, high- and low-pressure switches, coil and ambient temperature sensors, a transformer, compressor crankcase heater, high-capacity muffler, and a color-coded terminal strip for non-communicating set-up.

Rheem, a renowned global manufacturer of HVAC and water heating solutions, recently unveiled the industry's most efficient hybrid electric water heater. Named ProTerra for its unmatched efficiencies, this ENERGY STAR certified water heater from Rheem is over 400 percent more efficient compared to any standard electric tank-type water heater in market and is more eco-friendly than ever at up to 4.0 UEF. "Rheem is committed to developing cutting-edge products that benefit end-users and our environment," said Ankur Maheshwari, Senior Product Manager, Rheem. "Our top-of-the-line ProTerra water heater can save homeowners money upon purchase in the form of a $300 federal tax credit, and because the system requires minimal power to operate, its carbon footprint is the lowest in its class." adjust water temperatures The ProTerra's compact design makes it a perfect tank replacement for even the home's smallest spaces. The system is available in the widest selection of gallon sizes in its category – 40, 50, 65, 80 – to support various hot water needs, and the ProTerra with LeakGuard model is now the industry's only hybrid water heater with built in leak detection and auto shutoff that limits water loss from the tank to no more than 20 ounces. LeakGuard protects the home against water damage, providing peace of mind for end-users. This all-new hybrid water heater also has Rheem's exclusive EcoNet Wifi technology built in. Once connected through the EcoNet mobile app, users can monitor the system from any location, adjust water temperatures for controlled comfort and receive maintenance alerts to ensure the system continues to run smoothly without interruption. detailed system diagnostics Plumbers can access detailed system diagnostics through Rheem's Contractor App Additionally, through the EcoNet mobile app, users can access Rheem's Hot Water Availability feature which indicates how much hot water is available in the tank, preventing any cold shower surprises. Other advanced features include scheduling around peak electricity rates, an energy usage tracker to manage consumption without sacrificing comfort and five operating modes to balance between energy usage and hot water availability. Plumbers can access detailed system diagnostics through Rheem's Contractor App, which shortens service visits and improves credibility in the field. The ProTerra has all serviceable components on the front of the unit, which also saves plumbers valuable time on a jobsite. Another benefit to plumbers is the unit's zero clearance requirement on the sides. This makes earthquakes straps easy to install, providing an extra benefit in California where earthquake straps are code. efficient water heater "Our ProTerra hybrid water heater is not only the most efficient water heater available; it is also NEEA Tier 4 certified and comes with CTA 2045 adaptor with full Demand Response capability out of the box," said Scott Cohen, Senior Manager, Rheem. "This level of product efficiency is Rheem's ongoing priority when developing new innovations and supports the company's 'Greater Degree of Good' sustainability initiative which includes reducing GHG emissions by 50 percent." The ProTerra qualifies for the highest level of energy rebates, will save homeowners up to nearly $500 in annual energy costs1 and will pay for itself within two years2. For more information on utility rebates, the local utility provider can be contacted or the website can be visited.

During the Annual Meeting, members of the association for the region’s HVACR manufacturers elected Mr Brian Suggitt, Managing Director, Systemair UAE, as President supported by Mr Tariq Al Ghussein, CEO of local company Taqeef as Vice-President. Thanks to continuous growth in previous years, the member gathering saw the approval of lower membership fee structures for its members, which ensures the longevity of the Association for the years ahead. The new Board further consists of Mr Asim Ansari (Export Sales Manager, Airedale), Mr Dani Elamana (Technical Director, Camfil Middle East), Mr Rafael van Eijcken (General Manager, Baltimore Aircoil Middle East), Mr Frank Taaning Grundholm (VP - Global HVACR Sales, ABB), Mr Iyad Al Jurdy (Senior Manager, LG Electronics), Mr Srinivasan Rangan (Director of Marketing and Product Management, Rheem MEA), Mr Naveen Sivakumar (Head of Marketing and Business Development, Danfoss) and Mr David Jacobs (VP and Managing Director EMEA, Baltimore Aircoil) as Born Board member elected by the Eurovent Association. Making a difference by driving change I am excited to see so much energy and enthusiasm in the new board" Eurovent Middle East has seen considerable growth and development since its inception and saw an unprecedented number of technical meetings in 2019. The industry body was active on multiple regulatory issues, supporting authorities with combined feedback from the industry, and its members with clarifications and the resolution of potential regulatory obstacles to free trade. In his third consecutive term steering the Association, Mr Suggitt has introduced a special theme for this year, “Making a difference by driving change.” The evolution of the group has been a remarkable example of the power of co-creation, as the newly elected President shares, “I am excited to see so much energy and enthusiasm in the new board.” Power of co-creation and cooperation “The development of the association from the beginning to now underlines the power of co-creation and cooperation. What we have achieved so far may not be immediately noticeable but would have never been able without the contributions and dedication of our members. We are competitors in the field, but what the field looks like is our common concern.” This should also encourage additional companies to consider a membership" Mr Tariq Al Ghussein, newly elected Vice-President adds, “People begin to gradually understand the benefits and opportunities an association provides. Having been in the board for over a year now and seeing the work, which was done, assures me that the path we’ve followed is the right one. I can only emphasise again that the region needs much more cooperation among the industry and its various partners, be it government entities, consultants or contractors.” Reduced membership fees Speaking on the reduced membership fees and other changes, Mr Markus Lattner, Managing Director of Eurovent Middle East explains, “It was initially planned to lower the fees when we reached a certain threshold of revenues. The growth in membership since the beginning allows us to make this step earlier than intended and thus easier for our members in an economically more difficult time.” “This should also encourage additional companies to consider a membership. Further steps include extending our reach into Egypt and Pakistan and publishing dedicated technical recommendations to provide guidance on key technologies. The acclaimed HVACR Leadership Workshops will be continued with Building Retrofit, Cold Chain and Data Centre Cooling events over the next three months.”